This article describes the best practices for taking a measurement
Wait 3 minutes between measurements to avoid device overheating
rPPG - Face scan
In order to get accurate vital-sign readings, follow the guidelines below:
Device
- Ensure battery level is above 20% and not in power-save mode.
- Ensure your camera lenses are clean and unscratched.
- Place device on a stand about 30 cm away from your face.
- Position the device with the selfie camera at eye level and parallel to
the face. - Use a stand to reduce shaking and movements of the device.
Subject
- Sit still during the measurement.
- Ensure your feet are placed flat on the floor and your legs are
uncrossed. - Make sure your face is fully exposed, ensuring it is not covered by hair or accessories (i.e., mask, sunglasses, hat).
- Avoid moving or talking throughout the measurement and remain focused on the screen until the measurement is complete.
Environmental Conditions
- Ensure your face is evenly illuminated
- Avoid measuring in locations with multiple light sources (preferably a
single light source directed towards the face). - Settle into a position where no light sources are directed toward the
camera (e.g., by sitting against a wall). - Ensure neither the camera nor the area in the frame is exposed to
direct sunlight. - Avoid movement of other persons behind or within your vicinity.
- Avoid highly reflective objects in the surrounding area, including
mirrors, glass windows, tables, etc. - Ensure the level of the light illuminating your face is a minimum
of 400 lux. - It is recommended that you use a cold light (>4500K) and not a
monochromatic light source.
PPG - Finger scan
When using the By Finger (PPG) mode, following these best practice guidelines:
Device
- Ensure battery level is above 20% and not in power-save mode.
- Ensure your camera lenses are clean and unscratched.
- Keep your mobile device in a fixed position throughout the entire measurement.
- The device should be held by hand.
Subject
- Sit comfortably and use your free hand for support.
- Ensure your feet are placed flat on the floor and your legs
are uncrossed. - Hold your phone in a comfortable and stable position.
- Place the index finger on the appropriate rear camera and assure
it fully covers the lens. Do not cover the flashlight. You will see
your finger on the preview display when your finger is placed on
the appropriate camera. - Apply moderate and constant pressure when placing your finger
on the camera. - Avoid moving or talking throughout the measurement and remain
at rest throughout the measurement. - Avoid moving your finger during the measurement.
- iPhone users: cover both the rear flashlight and camera with your index finger.
- Android users: cover the rear camera with your index finger without covering the rear flashlight.
Environmental Conditions
- Measurements should not be taken in complete darkness.
Polar Devices
Currently, the Binah SDK supports the Polar Verity Sense device.
Mobile Device
- Ensure that your mobile device has a battery level above 20% and is
not in power-saving mode. - Stay within the Bluetooth® range of your smartphone throughout the
measurement to avoid connection or signal disruptions.
Polar Verity Sense Sensor
- Ensure that your Polar Verity Sense™ battery is sufficiently charged.
- Turn on your Polar Verity Sense™ by pressing the silver button located
on the side of the sensor. - Verify that there is a green light visible on the back of the sensor.
- Pair your Polar Verity Sense™ with your smartphone via Bluetooth®.
- Wear the Polar Verity Sense™ snugly over clean skin on the
outer-center part of your non-dominant upper arm and fasten the
band securely. - Ensure the sensor is in direct contact with your skin (underneath
clothing). Avoid placing it over tattoos or adjusting it during the
measurements. - When putting on the armband, ensure that the device’s power button
is facing upwards and that the “POLAR” label on the device is not
upside down. This ensures that the sensor is positioned properly on
your skin.
Subject
- Act naturally during the measurement. Avoid unnecessary movements
or adjustments to the sensor on your skin.
Comments
0 commentsPlease sign in to leave a comment.